— FOOD-GRADE GREASES
Klüber NSF H1
Food-Grade Greases.
The Klüber food-grade grease range covers hundreds of formulations. Droplex supplies the full range and specifies the right product for each application in your plant. Not the nearest available. The right one.
— FOOD-GRADE GREASES BY APPLICATION
Find the right grease
for your application.
The right food-grade grease depends on the operating condition — not on which product is readily available. Each application category below covers a specific set of conditions. Droplex identifies which Klüber formulation is right for your specific equipment and environment.
The Klüber food-grade grease range is extensive. The products listed under each category below are representative examples. Droplex has access to the full Klüber portfolio — including formulations for applications not shown here. Speak to a technical advisor to identify the right product for your specific application.
GENERAL USE
General-Purpose Food-Grade Greases
For standard bearings, conveyors, and general plant equipment where a single NSF H1 compliant grease simplifies the lubrication programme without compromising food safety. Available in mineral and synthetic base oil formulations.
REPRESENTATIVE PRODUCTS
- Klüberlub NH1 11-222 mineral · water resistant
- Klübersynth UH1 14-222 synthetic · extended life
HIGH LOAD
High-Load Food-Grade Greases
For mixers, pellet presses, kneaders, extruders, and other heavily loaded equipment where standard food-grade greases break down under pressure and cause accelerated bearing wear. Formulated with EP additives approved for food contact.
REPRESENTATIVE PRODUCTS
- Klüberfood NH1 94-402 high load · washdown resistant
WET ENVIRONMENTS
Washdown Resistant Food Grade Greases
For equipment exposed to frequent water washdowns, high-pressure cleaning, or steam sterilisation — where conventional greases wash out of bearings during the cleaning cycle, leaving the bearing unprotected between relubrication intervals.
REPRESENTATIVE PRODUCTS
- Klübersynth UH1 14-151 superior washdown resistance
HIGH SPEED
High-Speed Food-Grade Greases
For centrifuges, filling machines, packaging lines, and other high-speed applications where standard greases churn at high rotational speeds — generating heat, increasing friction, and causing premature bearing failure. Low-viscosity formulations designed for high-speed operation.
REPRESENTATIVE PRODUCTS
- Klübersynth UH1 14-31 low viscosity · high speed
Why Food-Grade Grease Fails in Most Plants
Most plants use:
- One grease for everything
- Incorrect relubrication practices
- Greases that don’t withstand washdowns or load
The result:
- Frequent bearing failures
- Over-greasing and contamination risk
- Audit exposure
How We Think Differently
We don’t start with products.
We start with your application and risk points.
Then we match the right grease to the job.
What You Get Right
- NSF H1 compliant lubrication (ISO 21469, Halal, Kosher aligned)
- Reliable performance in washdown, heat, and humidity
- Extended relubrication intervals
- Reduced failures and maintenance effort
- Audit-ready lubrication practices
Engineering Insight
Multi-purpose grease simplifies inventory.
Application-specific grease improves reliability.
Packaging That Fits Your Operation
- 60 g tubes — precision use
- 400 g cartridges — standard grease guns
- 1 kg cans — routine maintenance
- 25 kg buckets — plant-wide use
- 180 kg drums — high consumption
We help you match pack size to usage, reducing waste and contamination.
Measured Impact
- 2–4× longer component life
- Up to 40% lower maintenance costs
- Reduced energy consumption
- Improved audit readiness (documentation (NSF, ISO, Halal, Kosher)
Beyond Products – Droplex Support
- Lubrication audits & assessments
- Application-based grease selection
- Food-safe lubrication training
- Troubleshooting & performance tracking
Take The Next Step
Food-grade lubrication is too critical to guess.
Let’s get it right.